- Colors: Standard (patterned surface with slight green hue); Amethyst (standard cast with a blue coating); Clear (no pattern or hue)
- Optional coatings: Low E (Plus 1.7), Sun protection (Antisol®)
- Available in long channel lengths -- up to 23 ft (7 m)
- Allows natural light through while maintaining privacy
- Energy efficient
- Excellent light transmission
- Can be filled with Nanogel® insulation (optional)
- Sound insulation (up to 42 dB uninsulated, 44 dB with Nanogel® insulation)
- Can be utilized in curved walls
- Installs vertically or horizontally
- Aluminum perimeter frame provides additional structural strength
- Minimal maintenance
- Proven performance -- used in Europe for more than 30 years
- May be tempered or filmed to meet impact safety requirements
- Most channels available with pinstripe wires
| Approx. face width: |
| K22 |
K25 |
K32 |
| 9.13 in (232 mm) |
10.31 in (262 mm) |
13.03 in (331 mm) |
|
| Approx. flange height: |
2.36 in (60 mm) |
| Thickness: |
.28 in (7 mm) |
| Max length: |
Up to 23 ft (Varies according
to windload and project requirements) |
Weight/ft2 of channel surface
(including frame & components): |
12 lbs / ft2 dual glazed
7 lbs / ft2 single glazed |
| Light Transmission: |
70-75% (uninsulated, varies with coating) |
| U-Value (glass only): |
.49 (uninsulated), .40 (Low-E uninsulated), .21 (Low-E with 16 mm Nanogel® insulation), .19 (Low-E with 25 mm Nanogel® insulation) |
| Solar Heat Gain Coefficient: |
.70 (uninsulated), .45 (Low-E uninsulated), .42 (Low-E with 16 mm Nanogel® insulation), .31 (Low-E with 25 mm Nanogel® insulation) |
| STC Rating: |
42 dB (uninsulated), 44 dB (with Nanogel® insulation) |
Pilkington Profilit can be filled with Nanogel® aerogel, a new class of lightweight insulation material produced by Cabot Corporation which is ideally suited for daylighting design. The exceptional thermal performance of Nanogel aerogel helps increase energy efficiency. Nanogel aerogel also promotes soft, even light dispersion, reduces unwanted noise and resists condensation. TGP is the exclusive supplier of Nanogel aerogel.
Benefits
| Increases Light Diffusion: |
Eliminates glare, allows soft, even, light dispersion |
| Improves Acoustic Performance: |
Minimizes unwanted noise |
| Exceptional Thermal Performance: |
Reduces heat loss and minimizes solar heat gain |
| UV Stable: |
Maintains performance over time |
| Resists Moisture: |
Prohibits growth of mold, mildew and fungus |
| Provides Green Solutions: |
Reduces building design loads and conserves energy |
| Adheres to Guidelines: |
Meets and exceeds strict building codes |
Colors
Standard Cast
Patterned surface with a slight green hue
Amethyst
Standard Cast with a blue coating
Antisol®
Standard Cast with a bronze hued performance coating to control solar heat gain
Low-E
Standard cast with a performance coating for improved U-Values
Clear
No pattern or hue
Textures
Wave
Standard Cast with a ridge texture
Wave Amethyst
Standard Cast with a blue coating and a ridge texture
Pilkington Profilit should be installed in accordance with approved shop drawings -- plumb, level, square and free from warp or twist while maintaining dimensional tolerances and alignment with surrounding construction.
Erect framing, vinyl spacer and glass in accordance with manufacturer's printed installation instructions. Seal glass units continuously on both sides of glass between frame and glass and between linear glass units. Install perimeter joint sealant and backing materials between assemblies and adjacent construction.
Profilit has been tested to meet the following standards: AAMA 501.4, AAMA 101, AAMA 1801-97, AAMA/NWWDA 101/1, S.297, ASTM F 588-97, NFRC 100-97, ANSI Z97.1-1984, CPSC 16CFR 1201, Category II (with safety film). All testing carried out by Architectural Testing Inc., York, PA. Formal test reports are available by contacting Technical Glass Products.
(Details shown are not thermally broken.)
Please see our complete 3-part CSI format Profilit specifications.
Technical Glass Products can also offer project specific assistance upon request.
To obtain CAD details for this product, please use our CAD request form.
To obtain BIM models for this product, please use our BIM Model request form.